Part 2 of 11

A tracker built for salt, spray and vibration

Jet skis are a hard place for electronics: constant spray, the odd capsize, wave slam, heat on the dock and riders who will poke anything with a lid. The SeaTrace tracker is designed for that environment first.

UV-stable lidRF-transparent window GNSS, L6 and LTE antennasL1/L5/L6 patch, flex LTE Main boardGNSS, LTE-M/NB-IoT, MCU, IMU, flash LiFePO4 Backup battery5,000 mAh, heat-safe chemistry Potted base and gland12 V, ignition sense, gasket
Exploded view of the SeaTrace tracker. Final component choice is confirmed after field testing.

What’s inside

A sealed unit about the size of a paperback, mounted out of sight under the rear cowling. It is powered by the jet ski and carries its own backup battery for when that power disappears.

  • QZSS-enhanced multi-GNSS with MADOCA-PPP for decimetre positions
  • Low-power cellular with on-board storage for coverage gaps
  • Motion, ignition and tamper sensing to tell riding from towing
  • Submersible, UV-stable enclosure with no hull drilling
PartSpecificationWhy it matters
PositioningQZSS (Michibiki) with GPS, Galileo, BeiDou and GLONASS. Dual-band L1/L5 plus QZSS L6 for MADOCA-PPP corrections and QZNMA authentication.Decimetre-level positions over the bay and protection against spoofing. See Part 3.
ConnectivityLTE-M and NB-IoT, LTE Cat-1 fallback where needed. Soldered eSIM.Low power, good coastal reach; a soldered SIM can’t be pulled by a thief.
Storage8 MB flash ring buffer, about 100,000 fixes.No gaps in the track when coverage drops at the far side of the bay.
Power input9 to 32 V from the jet ski, isolated DC-DC, reverse-polarity and surge protection.Survives engine starts and wiring faults.
Backup battery5,000 mAh LiFePO4.Keeps reporting if main power is cut, and tolerates heat on a sunny dock.
EnclosureIP68 (1.5 m for 60 minutes) and IP66 jet spray. UV-stable ASA/PC, stainless fixings.Capsize submersion and daily hose-downs.
Shock and vibrationTested to IEC 60068-2-6 and 60068-2-27 profiles.Wave slam at speed, every ride, all season.
Sensors6-axis IMU, ignition and engine-hours sense, lid switch, light sensor, supply voltage.Tells riding from towing, counts engine hours, detects tampering.
OptionalRider buzzer and LED.Warns the rider directly as they approach a boundary.
CertificationSIRIM QAS certification for MCMC compliance, arranged before deployment.Radio equipment must be certified before use in Malaysia.

Antenna placement and mounting

Most tracking problems on small craft come from where the antenna sits, not from the receiver. Water, metal and the rider’s body all block or reflect satellite signals.

  • Mount under the rear seat cowling or storage hatch lid, which is plastic and faces the sky
  • Keep the antenna at least 30 cm from the engine, exhaust and any metal fuel tank
  • Orient the antenna window upward; the IMU is calibrated to that orientation at install
  • Use marine adhesive mounts plus stainless fixings, with no holes below the waterline
  • Route the 12 V and ignition lead through a sealed gland, fused at the battery
Engine bay: avoid Tracker here Rear cowling, clear sky view Handlebars and bow Seat Stern
Recommended position on a typical sit-down jet ski. Exact location is confirmed per model during the site survey.

Reporting interval and battery life

The jet ski’s own battery powers the tracker in normal use, so reporting rate on the water is driven by data cost and map smoothness, not battery. The backup battery matters when main power is cut, which is exactly when a thief has disconnected it.

Move the slider to see the trade-off. These are planning estimates for the backup battery alone; real figures are measured in field testing.

Adaptive by default. The tracker does not use one fixed interval. It reports every 10 seconds while riding and drops to a 30-minute heartbeat overnight, waking instantly on motion.

10 s
108 mAaverage draw
39 hon backup battery alone
9.7 MBdata per unit per month, 10 active hours a day

Assumes a 5,000 mAh backup at 85% usable capacity, continuous GNSS below 60 seconds and duty-cycled GNSS above it.

Connectivity and store-and-forward

Coverage on the water is rarely perfect, especially behind headlands or near islands. The tracker never discards a fix just because it can’t send it.

If the link drops for 20 minutes, the 120 fixes stored meanwhile arrive in order within seconds of reconnecting. The map backfills the track and the timeline marks the gap, so staff can see that the unit was out of contact rather than stationary.

  1. Fix taken

    Position, time, speed, heading, satellite count and accuracy estimate.

  2. Queued in flash

    Every fix enters the on-board buffer first, whether or not the link is up.

  3. Sent when possible

    Batched over MQTT on TLS; queued fixes are sent oldest first.

  4. Acknowledged

    The server confirms receipt by sequence number.

  5. Released

    Only acknowledged fixes leave the buffer, so nothing is lost in transit.

Tamper and safety sensing

Each sensor answers a specific question about the unit. Together they let the platform tell an innocent event from a theft or an accident.

Case opened

Lid switch and light sensor fire together. Critical alert with the last position and the staff member on shift.

Main power cut

The tracker switches to backup, raises its reporting rate and sends an immediate alert. A classic first step in theft.

Moving with ignition off

Steady 5 to 15 km/h with the engine off and low vibration is the signature of a unit being towed. Critical alert after hours.

Capsize

IMU tilt beyond 120 degrees for more than 10 seconds. Safety alert to dock staff and the patrol boat with position.

Immobile on the water

No movement for 3 minutes during a rental, away from the dock and recovery point. Possible breakdown or rider in difficulty.

Antenna blocked

Sudden fall in satellites and accuracy while the IMU shows motion. Logged, and escalated if it persists.

Installation

Around 30 to 45 minutes per unit, done at the dock or in the workshop, with no hull drilling below the waterline. A technician can fit a fleet of 20 in three days.

  1. Survey the model

    Confirm mounting position and cable route for each jet ski model in the fleet.

  2. Mount the tracker

    Marine adhesive plus stainless fixings under the rear cowling, window facing up.

  3. Wire power and ignition

    Fused 12 V feed and ignition sense through a sealed gland.

  4. Calibrate and register

    IMU orientation set, tracker bound to the unit’s fleet number in the platform.

  5. Verify on the water

    Short test ride; confirm track, zones and alerts on the staff app.